Install Release Bearing Hub Clip
a Install the release bearing hub clip to the release bearing assy. 18. INSTALL CLUTCH RELEASE FORK SUB-ASSY a Apply release hub grease to the release fork and release bearing assy contact, release fork and push rod contact and release fork pivot points. Part No. 08887-01806, RELEASE HUB GREASE or equivalent b Install the release fork to the release bearing assy. 19. INSTALL CLUTCH RELEASE BEARING ASSY a Apply the clutch spline grease to the input shaft spline. Sealant Part No. 08887-01706,...
Inspect Evap System Line 1
a Warm up and stop the engine. 1 Warm up the engine to normal operating temperature. b Install a vacuum gauge EVAP control system test equipment vacuum gauge to the EVAP service port on the purge line. c Connect the hand-held tester to the DLC3. e Turn the hand-held tester main switch ON. f Use the ACTIVE TEST mode on the hand-held tester to operate the VSV for EVAP. g Check the vacuum while the engine is idling. Standard
Knock Sensor Azfe Replacement
1. DRAIN ENGINE COOLANT See page 16-6 2. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE 3. REMOVE THROTTLE BODY ASSY See page 10-6 a Remove the 5 bolts, 2 nuts, intake manifold and gasket. a Disconnect the knock sensor connector. b Remove the nut and knock sensor. a Install the knock sensor with the nut. Torque 20 N m 204 kgf cm, 15 ft Ibf b Connect the knock sensor connector. a Install a new gasket and the intake manifold with the 5 bolts and 2 nuts. Torque 30 N m 306 kgf cm, 22 ft Ibf 8....
Steering Sensor Replacement
2. SEPARATE BATTERY NEGATIVE TERMINAL 3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 4. REMOVE STEERING WHEEL COVER LOWER NO.2 5. REMOVE STEERING WHEEL COVER LOWER NO.2 4 SPOKE STEERING WHEEL ASSY 6. REMOVE STEERING WHEEL COVER LOWER NO.3 3 SPOKE STEERING WHEEL ASSY 7. REMOVE HORN BUTTON ASSY See page 60-25 8. REMOVE STEERING WHEEL ASSY See page 50-9 or 50-21 SST 09950-50013 09951-05010, 09952-05010, 09953-05020, 09954-05021 9. REMOVE INSTRUMENT CLUSTER FINISH PANEL See page 71-16 10. REMOVE...
Replacement Xof
Wash off the brake fluid immediately if it comes into contact with a painted surface. 3. REMOVE BRAKE MASTER CYLINDER SUB-ASSY See page 32-23 a Remove the bolt and separate the vacuum hose from the vacuum hose bracket. b Slide the clip and disconnect the vacuum hose from the brake booster. 5. REMOVE FRONT DOOR SCUFF PLATE LH See page 71-16 6. REMOVE COWL SIDE TRIM SUB-ASSY LH See page 71-16 7. REMOVE INSTRUMENT PANEL SUB-ASSY UPPER See page 71-16 a Remove the clip and push rod pin. 9. REMOVE...
Inspect Vacuum Switching Valve Assy For Evap 1
a Check the VSV for open circuit. 1 Measure the resistance. If the resistance is not as specified, replace the VSV assy. 1 Check that air does not flow from the port as shown in the illustration. 2 Apply battery positive voltage across the terminals. 3 Check that air flows from the ports. If the result is not as specified, replace the VSV assy.
Adjust Hood Subassy
a Loosen the hood side hinge bolts. b Adjust the clearance so that it will be in the standard value, by moving the hood. c Tighten the hood side hinge bolts after adjustment. Torque 26 Nm 265 kgfcm, 19 ft Ibf d Adjust the height of the hood front end by the cushion gum. The cushion gum goes up and down by turning it. e Using a screwdriver, remove the hood lock release lever cover. Tape the screwdriver tip before use. NOTICE Removing the protector damages the clips inside the protector, and...
Push rod play at pedal top mm in
e Adjust the pedal free play and push rod play. 1 Remove the instrument panel sub-assy upper. 2 Remove the instrument panel insert sub-assy lower LH. 4 Loosen the lock nut and turn the push rod until the free play and push rod play are correct. 6 After adjusting the pedal free play, check the pedal height. 8 Install the instrument panel insert sub-assy lower LH. 9 Install the instrument panel sub-assy upper. f Check the clutch release point. 1 Pull the parking brake lever and install wheel...
Front Brake Components
Front Disc Brake Cylinder Mounting LH Front Disc Brake Cylinder Mounting LH Nm kgfcm, ft lbf Specified torque Non-reusable part Lithium soap base glycol grease Disc brake grease Cylinder Boot Front Disc Brake Cylinder Slide Pin No.2 Nm kgfcm, ft lbf Specified torque Front Disc Brake Pad Wear Pad Support Plate No.2 Indicator Plate Front Disc Brake Pad Support Plate No.1 Non-reusable part Lithium soap base glycol grease Disc brake grease
Remove Air Cleaner Cap Subassy
a Disconnet the MAF meter connector. b Disconnect the VSV connector. c Remove the ventilation hose No. 2. d Disconnect the emission tube No. 1 fuel hose. e Disconnec the vacuum hoses. f Remove the fuel vapor feed hose from the 2 hose clamps. g Loosen the air cleaner hose clamp bolt, and then remove the intake air resonator.
Front Axle Lh Hub Bolt Replacement
Replace the RH side by the same procedures with LH side. 2. DISCONNECT FRONT DISC BRAKE CALIPER ASSY LH SEE PAGE 30-8 a Using SST and a screwdriver or an equivalent to hold, remove the front axle LH hub bolt. SST 09628-10011 a Install a washer and nut to a new front axle LH hub bolt as shown in the illustration. b Using a screwdriver to hold, install the hub bolt by torqu-ing the nut. 7. INSTALL FRONT DISC BRAKE CALIPER ASSY LH SEE PAGE 30-8 Torque 103 N m 1,050 kgf cm, 76 ft Ibf
Caulk Lock Plate
a Lightly press SST against the lock plate in the order shown in the illustration. After repeating this a few times, fully caulk the lock plate by gripping the handle until stopped by the stopper plate. SST 09230-01010 Do not tap the areas protruding around the pipes, brackets or tank ribs. The points shown in the illustration and oil cooler near here A T cannot be tapped with the SST. Use pliers or similar objects and be careful not to damage the core plates. b Check the lock plate height H...
Remove Front Wheel Bearing Dust Deflector Lh No Wo Abs
a Mount the front drive outboard joint shaft assy LH in a soft jaw vise. b Using a screwdriver and a hammer, remove the front wheel bearing dust deflector LH No.2. 24. REMOVE FRONT DRIVE SHAFT LH HOLE SNAP RING a Using a screwdriver, remove the hole snap ring. 25. REMOVE FRONT DRIVE SHAFT DUST COVER LH a Using SST and a press, remove the front drive shaft dust cover LH. Be careful not to drop the inboard joint assy. 26. REMOVE FRONT DRIVE SHAFT DUST COVER RH a Using a press, remove the front...
FRONT AXLE HUB SUBASSY LH From July REPLACEMENT
Use the same procedures for the RH side and LH side. The Procedures listed below are for the LH side. 2. REMOVE FRONT AXLE HUB LH NUT SEE PAGE 30-8 SST 09930-00010 3. DISCONNECT SPEED SENSOR FRONT LH W ABS SEE PAGE 30-8 4. SEPARATE FRONT DISC BRAKE CALIPER ASSY LH a Remove the 2 bolts and separate the front disc brake caliper assy LH from the steering knuckle LH. NOTICE Use a string or other device to keep the brake caliper from hanging down by the flexible hose. 6. SEPARATE TIE ROD ASSY LH...
Inspect Valve Clearance
a Turn the crankshaft pulley, and align the timing notch with timing mark 0 of the No. 1 timing belt cover. b Check that the valve lifters on the No. 1 timing belt cover IN and EX are both loose. If not, turn the crankshaft 1 revolution 360- and align the mark as above. c Check the valves indicated in the illustration on the left. 1 Using a feeler gauge, measure the clearance between the valve lifter and camshaft. Valve clearance Cold 0.15 to 0.25 mm 0.006 to 0.010 in. 0.25 to 0.35 mm 0.010 to...
Inspect Fuel Cutoff Valve And Fill Check Valve 1
a Disconnect the vent line hose from the fuel tank see page 11-52 . b Connect the pressure gauge to the fuel tank. c Fill the fuel tank with fuel until full. d Apply pressure of 4 kPa 41 gf cm2, 0.58 psi to the vent port of the fuel tank. It is necessary to check the amount of fuel in the fuel tank. When the fuel tank is full, the float valve of the fill check valve is closed and no air can pass through. e Remove the fuel tank cap, and check that pressure drops. If pressure does not drop,...
Components Ghh
Drive Shaft Bearing Bracket Hole Snap Ring Front Suspension Arm Sub-assy Lower No.1 LH Nm kgf cm, ftlbf Specified torque Drive Shaft Bearing Bracket Hole Snap Ring Front Suspension Arm Sub-assy Lower No.1 LH DRIVE SHAFT PROPELLER SHAFT - DRIVE SHAFT, PROPELLER SHAFT, AXLE From July, I Front Wheel Bearing Dust Deflector RH No.2 Front Drive Outboard Joint Shaft Assy RH Front Axle Outboard Joint Boot RH No.2 Clamp Front Axle Outboard Joint Boot RH No.2 Clamp Front Drive Outboard Joint Shaft Assy...
Replacement Bqm
Disconnect the clutch start switch assy connector. Remove the nut and clutch start switch assy from the clutch pedal support. Install the clutch start switch assy with the nut. Torque 16 N m 160 kgf cm, 12 ft Ibf Connect the clutch start switch assy connector. 3. INSPECT CLUTCH START SWITCH ASSY SEE PAGE 42-19
Inspect Airfuel Ratio Compensation System 1
a Measure the voltage between the terminals of the ECM connectors. Standard
Valve Sub-assy Ventilation
1. REMOVE VENTILATION VALVE SUB-ASSY a Disconnect the PCV hose from the PCV valve. 2. INSTALL VENTILATION VALVE SUB-ASSY 1 Apply adhesive to 2 or 3 threads. Adhesive Part No. 08833-00070, THREE BOND 1324 or equivalent 2 Reinstall the PCV valve. Torque 19 N m 193 kgf cm, 14 ft Ibf b Connect the PCV hose to the PCV valve.
Drive Belt Mzfemzfe Replacement
2. REMOVE FRONT FENDER APRON SEAL RH 3. REMOVE V COOLER COMPRESSOR TO CRANKSHAFT PULLEY BELT NO.1 b Loosen adjusting bolt C and remove the belt. a Loosen bolts A and B, and remove the belt. a Install the belt on each pulley. b Using a bar, adjust the belt tension and tighten bolt B. Torque 43 N m 439 kgf cm, 32 ft Ibf Torque 43 N m 439 kgf cm, 32 ft Ibf 6. INSTALL V COOLER COMPRESSOR TO CRANKSHAFT PULLEY BELT NO.1 a Install the belt on each pulley. b Tighten adjusting bolt C, and adjust the...
1996 Toyota Camry Water Pump Replacement
1. DRAIN ENGINE COOLANT See page 16-27 3. REMOVE FRONT FENDER APRON SEAL RH 4. REMOVE V BELT NO. 1 See page 14-140 5. REMOVE VANE PUMP V BELT See page 14-140 6. REMOVE ENGINE MOVING CONTROL ROD See page 14-164 7. REMOVE ENGINE MOUNTING STAY NO.2 RH See page 14-164 8. REMOVE GENERATOR BRACKET NO.2 9. REMOVE CRANKSHAFT PULLEY See page 14-186 10. REMOVE TIMING BELT NO.1 COVER See page 14-186 11. REMOVE TIMING BELT NO.2 COVER See page 14-186 12. REMOVE ENGINE MOUNTING BRACKET RH 13. REMOVE TIMING...
For Vehicles Equipped With Srs Airbag And Seat Belt Pretensioner
The CAMRY is equipped with a Supplemental Restraint System SRS and seat belt pretensioner. Failure to carry out the service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing and lead to serious injury. Furthermore, if a mistake is made when servicing the SRS, it is possible that the SRS may fail to operate properly. Before servicing including removal or installation of parts, inspection or replacement , be sure to read the following section...
Adjustment
With the brake pedal depressed, shift while holding the shift lever knob button. The ignition switch must be Shift while holding the shift lever knob button in a When shifting the shift lever to each position, make sure that it moves smoothly, and the position indicator displays correctly. The positions which can be shifted without pressing the shift lever knob button The positions which can be operated only while pressing the shift lever knob button The positions which can be operated only...
Throttle Body Assy Azfe Components
Nm kgfcm, ft lbf Specified torque Water Bypass Hose Water Bypass Hose No.2 Gasket Throttle Control Motor amp Throttle Position Sensor Connector Nm kgfcm, ft lbf Specified torque Water Bypass Hose Water Bypass Hose No.2 Gasket Throttle Control Motor amp Throttle Position Sensor Connector
Floor Shift Assy Atm Components
Floor Shift Shift Lever Knob Sub-assy Indicator Lamp Wire Indicator Lamp bulb I Position Indicator Indicator Lamp Cap LampShade j J Floor Shift Lever Lock Pin Accessory Tool Floor Shift Parking Lock Cable N m kgf cm, ft lbf Specified torque
Front Door Components
Front Door Frame Sub-assy Rear Lower Front Door Handle Assy Outside W Front Door Frame Sub-assy Front Lower Front Door Lower Frame Bracket Garnish Power Window Regulator Master Switch Assy Front Door Window Regulator Sub-assy Front Door Inside fP Handle Bezel Plug N m kgf cm, ft Ibf Specified torque Non-reusable part k Precoated part
Replacement Rnm
Installation is in the reverse order of removal. 1. DISCONNECT BATTERY NEGATIVE TERMINAL SEE PAGE 60-1 2. REMOVE STEERING WHEEL COVER LOWER NO.2 3. REMOVE STEERING WHEEL COVER LOWER NO.3 4. REMOVE HORN BUTTON ASSY SEE PAGE 60-25 5. REMOVE CRUISE CONTROL MAIN SWITCH ASSY c Pull out the cruise control main switch assy in the direction shown by the arrow in the illustration. 6. INSTALL HORN BUTTON ASSY SEE PAGE 60-25 7. INSPECT HORN BUTTON ASSY SEE PAGE 60-17 8. CONNECT BATTERY NEGATIVE TERMINAL...
Incorrect electrode connection causes damage to the VSV Pay due attention when
4 Check that air does not flow from port A to port B. 5 Check that air flows from port A to port C. If the result is not as specified, replace the charcoal canister. NOTICE
Confirmation Test
a After completing repairs, confirm that the problem has been solved. If the problem does not recur, perform a confirmation test under the same conditions and in the same environment as when it occurred for the first time. -k In troubleshooting, the problem symptoms must be confirmed accurately. Preconceptions should be discarded in order to give an accurate judgement. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the...
Inspect Piston Ring End Gap
a Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm 4.33 in. from the top of the cylinder block. b Using a feeler gauge, measure the end gap. Specified end gap 0.22 to 0.892 mm 0.0087 to 0.0350 in. 0.50 to 1.35 mm 0.0197 to 0.0531 in. 0.10 to 0.73 mm 0.0039 to 0.0287 in. If the end gap is greater than the maximum, replace the piston ring. If the end gap is greater than the maximum even with a new piston ring, replace the cylinder block. 22. INSPECT...
Remove Clutch Master Cylinder Kit
a Using a pin punch 5 mm and hammer, drive out the slotted spring pin. b Remove the inlet union and grommet. c Loosen the lock nut, and remove the push rod clevis. d Remove the lock nut from the push rod. e Remove the boot from the cylinder body. f While pushing the piston rod, using snap ring pliers, remove the snap ring. g Remove the push rod from the cylinder body. NOTICE
FRONT DRIVE SHAFT From July OVERHAUL
Use the same procedures for the RH side and LH side. The Procedures listed below are for the LH side. 1. DRAIN AUTOMATIC TRANSAXLE FLUID A T TRANSAXLE SEE PAGE 40-37 2. DRAIN MANUAL TRANSAXLE OIL M T TRANSAXLE SEE PAGE 41 -3 4. REMOVE FRONT AXLE HUB LH NUT a Using SST and a hammer, unstake the staked part of the axle hub LH nut. Loosen the staked part of the lock nut completely, otherwise the screw of the drive shaft may be damaged. b While applying the brakes, remove the front axle hub LH...
General Information 1
A large number of ECU controlled systems are used in the CAMRY. In general, ECU controlled systems are considered to be very intricate, requiring a high level of technical knowledge to troubleshoot. However, most problem checking procedures only involve inspecting the ECU controlled system's circuits one by one. An adequate understanding of the system and a basic knowledge of electricity is enough to perform effective troubleshooting, accurate diagnoses and necessary repairs. Detailed...
Components Mjx
N m kgf cm, ft lbf Specified torque Breather hose Radiator Reserve Hose _COOLING - RADIATOR ASSY 2AZ-FE From July, 2003 _
Notice For Using Plate Type Lift
a Follow safety procedures outlined in its instruction manual. b Use a plate lift attachments rubber lifting blocks on top of the plate surface. c Refer to the table below to determine how to properly set the vehicle. Place the vehicle over the center of the lift. Place the attachments at the ends of the rubber plate surface, under the vehicle lift pad A and C in the illustration . Raise the plate slightly and reposition the vehicle so the top of the attachment B in the illustration is aligned...
Remove Automatic Transaxle Assy 1
a Remove the 2 bolts and nut. b Remove the exhaust pipe support bracket and exhaust pipe support bracket No.1 from the automatic transaxle. c Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench. There will be one green colored bolt. e Separate and remove the automatic transaxle. 15. REMOVE TORQUE CONVERTER CLUTCH ASSY 16. REMOVE TRANSAXLE CASE COVER UPPER a Remove the 3 bolts and transmission case cover upper. 17. INSPECT TORQUE...
Remove Intake Air Surge Tank
a Disconnect the throttle motor connector. b Disconnect the water by-pass hose No. 3. c Disconnect the water by-pass hose No. 2. d Disconnect the union to check valve hose. e Disconnect the ventilation hose. f Remove the 3 nuts and disconnect the pressure feed tube. g Remove the 2 bolts and engine hanger No. 1. h Remove the 2 bolts and surge tank stay No. 1. i Remove the 2 bolts and surge tank stay No. 2. j Using a socket hexagon wrench 8, remove the 4 bolts, k Remove the 2 nuts, emission...
Steering Pad Switch Lh Replacement
Installation is in the reverse order of removal. 2. DISCONNECT BATTERY NEGATIVE TERMINAL SEE PAGE 60-1 3. REMOVE STEERING WHEEL COVER LOWER NO.2 TMC MADE SEE PAGE 50-9 4. REMOVE STEERING WHEEL COVER LOWER NO.3 TMC MADE SEE PAGE 50-9 5. REMOVE HORN BUTTON ASSY SEE PAGE 60-25 6. REMOVE STEERING PAD SWITCH LH 4 SPOKE STEERING WHEEL ASSY b Disconnect the connector of cruise control main switch. Release the 2 pins and remove the steering pad switch LH. e w steering pad switch RH Remove the clamp....
Navigation Ecu Replacement
1. REMOVE LUGGAGE COMPARTMENT FLOOR MAT 2. REMOVE SPARE WHEEL COVER ASSY 3. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSY RH 4. REMOVE LUGGAGE COMPARTMENT TRIM HOOK NO.1 See page 76-8 5. REMOVE REAR FLOOR FINISH PLATE See page 76-8 6. REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH See page 76-8 a Disconnect the connectors and remove the 2 clamps. b Remove the nut and 2 bolts, then remove the navigation ECU. a Remove the 2 screws and disc player bracket. a Remove the 2 screws and disc player...
Remove Piston
a Gradually heat the piston to approxinately 80 to 90 C 176 to 194 F . b Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod. The piston and pin are a matched set. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.
Check Camshaft Timing Oil Control Valve Assy
a Connect the hand-held tester or OBD II scan tool to the DLC3. b Turn the ignition switch ON. c Start the engine and warmed it up. d Select the VVT from the ACTIVE TEST menu. e Check the engine speed when the OCV is operated by the hand-held tester. Standard If the result is not as specified, replace the OCV assy. 4. CHECK MASS AIR FLOW METER MAF meter NOTICE Perform the MAF meter inspection by following the procedures below. Only replace the MAF meter when both the LONG FT 1 value and MAF...
CHARCOAL CANISTER ASSY AZFEFrom July REPLACEMENT
1. REMOVE FUEL TANK ASSY See page 11-21 a Disconnect the fuel tank vent hose. 1 Push the connector deep into the charcoal canister assy to release the locking tab. b Disconnect the VSV connector for CCV. c Disconnect the fuel emission hose. d Disconnect the air inlet line hose. e Remove the 2 bolts and charcoal canister. 3. INSTALL CHARCOAL CANISTER ASSY Torque 39.2 N m 400 kgf cm, 29 in. Ibf 4. INSTALL FUEL TANK ASSY See page 11-21
Install Clutch Master Cylinder Assy
a Install the clutch master cylinder assy with the 2 nuts. Torque 12 N m 120 kgf cm, 9 ft Ibf 11. INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS W HOLE PIN a Apply MP grease to the contact surface of the hole pin and bush. b Connect the clevis to the clutch pedal assy with the hole pin. Install the hole pin from the left side of the vehicle. c Install the clip to the hole pin. 12. CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE a Using SST, connect the flexible hose tube. Torque 15 N m...
Inspect Front Disc Brake Pad Support Plate
a Inspect the front disc brake pad support plate No.1 and front disc brake pad support plate No.2 . HINT Make sure that both have sufficient rebound, have no deformation, cracks or wear, and that all rust and dirt is cleaned off. If necessary, replace the brake pad support plate. a Using a micrometer, measure the disc thickness. Standard thickness 28.0 mm 1.102 in. Minimum thickness 26.0 mm 1.024 in. If the disc thickness is less than the minimum, replace the disc. a Put matchmarks on the...
TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL AZFEFrom July REPLACEMENT
2. REMOVE FRONT FENDER APRON SEAL RH 3. REMOVE ENGINE COVER SUB-ASSY NO.1 4. REMOVE ENGINE MOVING CONTROL ROD W BRACKET a Remove the 3 bolts and control rod. 5. REMOVE ENGINE MOUNTING STAY NO.2 RH 6. REMOVE ENGINE MOUNTING BRACKET NO.2 RH 7. REMOVE FAN AND GENERATOR V BELT See page14-5 1 Using SST, loosen the pulley bolt. SST 09213-54015 91651-60855 , 09330-00021 2 Using SST, remove the pulley bolt and pulley. SST 09950-50013 09951-05010, 09952-05010, 09953-05020, 09954-05021 TIMING GEAR CASE...
Inspect Shift Lock Control Computer
a Using a voltmeter, measure the voltage at each terminal. HINT Do not disconnect the shift lock control unit connector. If the result is not as specified, replace the shift lock control unit. b Using an ohmmeter, measure the resistance between terminal E 1 and body ground. If the result is not as specified, replace the shift lock control unit.
Replacement Mpf
Do not separate the sensor from the bracket. 1. REMOVE CONSOLE PANEL UPPER REAR See page 71-16 2. REMOVE RR CONSOLE BOX See page 71-16 a Disconnect the yawrate sensor connector. b Remove the 2 bolts and yawrate sensor. a Install the yawrate sensor with the 2 bolts. Torque 12.5 N m 127 kgf cm, 9 ft Ibf b Connect the yawrate sensor connector. 5. INSTALL RR CONSOLE BOX See page 71-16 6. INSTALL CONSOLE PANEL UPPER REAR See page 71-16 7. PERFORM YAWRATE SENSOR ZERO POINT CALIBRATION See page 05-987
Hood Support Rod Replacement
a Using a screwdriver to hold the left spring, disengage the upper and lower parts of the support rod, and then remove the hood support rod. NOTICE Removal should be done while the hood is being held up. Install a metal socket onto the hood except a resinous one onto the body. After the installation, make sure that the socket is securely attached.