Connect No Vehicle Speed Sensor Connector
7. DISCONNECT SPEED SENSOR NT AND SP2 CONNECTORS 8. REMOVE SPEED SENSOR NT AND SP2 a Remove the 2 bolts, speed sensor NT and SP2. b Remove 2 O-rings from the speed sensor NT and SP2. 9. INSTALL SPEED SENSOR NT AND SP2 a Coat 2 new O-rings with ATF and install them to the speed sensor NT and SP2. b Install the speed sensor NT and SP2 with 2 bolts. Torque 5.4 N-m 55 kgf-cm, 48 in.-lbf 10. CONNECT SPEED SENSOR NT AND SP2 CONNECTORS
REMOVE AIR DUCT Vent Duct
a Disconnect the mode damper control link b Remove the 2 screws and the air duct. 1. CHECK HEATER RADIATOR FINS FOR BLOCKAGE If the fins are clogged, remove them with compressed air. 2. CHECK FITTING FRO CRACKS OR SCRATCHES Installation is in the reverse of removal See page AC-40 . Reassembly is in the reverse of disassembly See page AC-41 .
Disconnect the connector from RSA controller and inspect the connector on the
Ignition switch LOCK and radio switch ON Ignition switch ACC or ON and radio switch ON
Reassemble Shift Lock Solenoid
a Apply MP grease to the shift lock solenoid link. b Install the shift lock solenoid link and the pin to the shift lock solenoid plunger. c Install the shift lock solenoid link with shift lock solenoid plunger and the spring to the shift lock solenoid. 4. CONNECT SHIFT LOCK CONTROL ECU, SHIFT LOCK SOLENOID, SHIFT LOCK CONTROL SWITCH, INDICATOR LAMP WIRE AND 2 TRANSMISSION CONTROL SWITCH 5. REASSEMBLE SHIFT LEVER GUIDE HOUSING a Apply MP grease to the shift lever lock pin. b Install the shift...
Inspect Radio Receiver Assembly Circuit
Disconnect the connectors from the radio receiver assembly, and inspect the connector on the wire harness side. If the circuit is not as specified, inspect the circuits connected to other parts. lo 9 I 8 I 7 I 6 I 5 I 4 I 3 I 2 I 1 20 19 18 17 16 15 14 13 12 11 Check the wire harness between radio receiver assembly and the CD auto changer, between radio receiver assembly and power amplifier.
Reassemble Shift Lever Plate
c Install the shift lever seal. d Install the shaft lower control bush, the spacer, the 2 plate washers and the swivel. e Using pliers, install the clip. f Apply MP grease to 2 new O-rings. g Install the 2 O-rings, 2 new spacers, the plate washer, the control lever and the nut.
Atf Temperature Sensor Onvehicle Repair
1. REMOVE ENGINE NO.2 UNDER COVER 3. REMOVE OIL PAN See page AT-11 4. REMOVE OIL STRAINER See page AT-1 1 a Disconnect the 7 solenoid valve connectors. b Remove the 2 bolts and disconnect the 2 ATF temperature sensors. c Disconnect the solenoid connector. d Remove the bolt and the transmission wire harness 6. INSTALL ATF TEMPERATURE SENSOR a Install the transmission wire harness. Torque 5.4 N-m 55 kgf-cm, 48 in.-lbf c Connect the solenoid connector. d Connect the 7 solenoid valve connectors. e...
Inspect Antenna Motor Control Relay Circuit
Disconnect the connector from the relay and inspect the connector on wire harness side, as shown in the chart on the next page. If circuit is as specified, replace the relay.
Set On 1
1. CONNECT CHARGING HOSE TO MANIFOLD GAUGE SET 2. CONNECT QUICK DISCONNECT ADAPTERS TO CHARGING HOSES 3. CLOSE BOTH HAND VALVES OF MANIFOLD GAUGE SET 4. REMOVE CAPS FROM SERVICE VALVES ON REFRIGERANT LINES 5. CONNECT QUICK DISCONNECT ADAPTERS TO SERVICE VALVES Push the quick disconnect adapter onto the service valve, then the sleeve of the quick disconnect adapter downward to lock it.
w LEXUS navigation system REMOVE EMV
Remove the 3 screws, the 2 bolts and the EMV Remove the screw, the 2 bolts and the radio receiver bracket RH. Remove the integration control panel from the radio receiver. Remove the 2 screws, 4 bolts and the radio receiver c Disconnect the connector clamp. d Remove the 2 screws, 4 bolts and the radio receiver bracket RH. e Remove the integration control panel.
Reception Problems
Besides the problem of static, there are also the problems called fading, multipath and fade out. These problems are caused not by electrical noise but by the nature of the radio waves themselves. Besides electrical interference, AM broadcasts are also susceptible to other types of interference, especially at night. This is because AM radio waves bounce off the ionosphere at night. These radio waves then interfere with the signals from the same transmitter that reach the vehicle's antenna...
Components Jrk
Nm kgfcm, in. lbf Specified torque
Disconnect Liquid And Suction Tubes
a Using SST, remove the 2 piping clamps. SST 09870-00025 Liquid tube 09870-00015 Suction tube Confirm the direction of the piping clamp claw and SST referring to the illustration on the caution label. 2 Push down SST and release the clamp lock. NOTICE
Actuator Rod Tacoma
1. REMOVE TRANSFER SHIFT LEVER KNOB 2. REMOVE UPPER CONSOLE PANEL See page BO-84 3. SEPARATE NO. 1 FLOOR SHIFT GEAR SHIFTING ROD b Remove the nut and separate the No. 1 floor shift gear shifting rod from the connecting rod swivel. 4. REMOVE FLOOR SHIFT LEVER ASSEMBLY Torque 8.3 Nm 85 kgfcm, 73 in.lbf c Remove the floor shift lever assembly.
Remove Blower Motor
b Remove the 3 screws and the blower motor. 4. REMOVE WIRE HARNESS Remove the screw and the wire harness. 1. INSPECT AIR INLET SERVOMOTOR OPERATION See page DI-1357 2. INSPECT AIR INLET DAMPER POSITION SENSOR CIRCUIT See page DI-1348 Installation is in the reverse of removal See page AC-55 . Reassembly is in the reverse of disassembly See page AC-56 .
Set On
1. CONNECT CHARGING HOSE TO MANIFOLD GAUGE SET 2. CONNECT QUICK DISCONNECT ADAPTERS TO CHARGING HOSES 3. CLOSE BOTH HAND VALVES OF MANIFOLD GAUGE SET 4. REMOVE CAPS FROM SERVICE VALVES ON REFRIGERANT LINES 5. CONNECT QUICK DISCONNECT ADAPTERS TO SERVICE VALVES Push the quick disconnect adapter onto the service valve, then the sleeve of the quick disconnect adapter downward to lock it.
Inspect Magnetic Clutch Relay Continuity
Apply B between terminals 57 and 65. If continuity is not as specified, replace the engine room J B. 3. INSTALL ENGINE ROOM J B If continuity is not as specified, replace the engine room J B. 3. INSTALL ENGINE ROOM J B
Inspect Air Outlet Servomotor Operation
a Connect the positive lead from the battery to terminal 6 and the negative - lead to terminal 7. b Connect the negative - lead from the battery to each terminal and check that the shaft rotates at each position, as shown in the illustration. If operation is not as specified, replace the servomotor. 4. INSTALL AIR OUTLET SERVOMOTOR a Install the air outlet servomotor with the 3 screws.
Evacuate Air From Refrigeration System
a Connect the vacuum pump adapter to the vacuum pump. b Connect the center hose of the manifold gauge set to the vacuum pump adapter. c Open both the high and low hand valves and run the vacuum pump. d After 10 minutes or later, check that the low pressure gauge indicates 750 mmHg 30 in. Hg minimum. If the reading is 750 mmHg 30 in. Hg close both hand valves of the manifold gauge set and stop the vacuum pump. Check the system for leaks and repair if necessary. e Close both the high and low...
DIAGNOSIS FUNCTION Main AVCLAN
For shifting to diagnosis mode, turn the ignition switch ON and push the DISC switch 3 times while pressing ch1 and ch6 switches. To exit the diagnosis mode, push the DISC switch for 1.7 sec. or turn the ignition switch to ACC or OFF. After the diagnosis start-up, the system enters the element check mode. Check that the all elements light up. By pressing the TUNE UP switch, the system enters the Service Check Mode. 1 Element check mode is started at the same time with the switch check mode. 2...
Use the refrigerant recovery recycling machine to recover the refrigerant
3. CHARGE REFRIGERANT INTO REFRIGERATION SYSTEM If there is no leak after refrigerant leak check, charge the proper amount of refrigerant into the refrigeration system. CAUTION Do not run the engine when charging the system through the high pressure side. Do not open the low pressure hand valve when the system is being charged with liquid refrigerant. a Open the high pressure hand valve fully. b Charge specified amount of refrigerant, then close the high pressure hand valve. No bubbles in the...