See page DI inspection procedure Fuv
CHECK:
- ON
Spiral Cable
^ Airbag J Sensor "I Assembly
AB0119 H01001 H02146
CHECK:
Turn the ignition switch to ON.
For the connector (on the spiral cable side) between the spiral cable and the steering wheel pad (D squib), measure the voltage between D+ and body ground.
Voltage: 0 V
Check airbag sensor assembly.
- D Squib
DLC3
DTC B0103/12
DLC3
CG TC
H01002
H02144 AB0119 H10600 W02043
CG TC
H01002
H02144 AB0119 H10600 W02043
DTC B0103/12
H10608
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect D+ and D- of the connector (on the spiral cable side) between the spiral cable and the steering wheel pad (D squib).
(c) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 20 seconds.
(b) Clear the DTC stored in memory (See step 5 on page DI-509).
(c) Turn the ignition switch to LOCK, and wait at least for 20 seconds.
(d) Turn the ignition switch to ON, and wait at least for 20 seconds.
DTC B0103/12 is not output.
HINT:
Codes other than code B0103/12 may be output at this time, but they are not relevant to this check.
H10608
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect negative (-) terminal cable from the battery, and wait at least for 90 seconds.
(c) Connect the steering wheel pad (D squib) connector.
(d) Connect negative (-) terminal cable to the battery, and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 20 seconds.
(b) Clear the DTC stored in memory (See step 5 on page DI-509).
(c) Turn the ignition switch to LOCK, and wait at least for 20 seconds.
(d) Turn the ignition switch to ON, and wait at least for 20 seconds.
DTC B0103/12 is not output.
HINT:
Codes other than code B0103/12 may be output at this time, but they are not relevant to this check.
From the results of the above inspection, the malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check. If the malfunctioning part can not be detected by the simulation method, replace all SRS components including the wire harness.
-I Airbag
] Sensor ^ Assembly
D Squib
Spiral Cable
H01000 AB0119 H02146
-I Airbag
] Sensor ^ Assembly
H02202
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the connector between the airbag sensor assembly and the spiral cable.
CHECK:
(a) Turn the ignition switch to ON.
(b) For the connector (on the spiral cable side) between the spiral cable and the steering wheel pad (D squib), measure the voltage between D+ and body ground.
Voltage: 0 V
6 Check harness between airbag sensor assembly and spiral cable.
CHECK:
Turn the ignition switch to ON.
For the connector (on the spiral cable side) between the spiral cable and airbag sensor assembly, measure the voltage between D+ and body ground.
Voltage: 0 V
Repair or replace harness between airbag sensor assembly and spiral cable.
From the results of the above inspection, the malfunctioning part can now be considered normal. To make sure of this, use the simulation method to check. If the malfunctioning part can not be detected by the simulation method, replace all SRS components including the wire harness.
|
DI6P7-20 | ||
|
DTC |
B0105/53 |
Short in P Squib Circuit |
Post a comment