A
in order to reduce the risk of damage to the accessory vehicle and to ensure a quality installation. TOOLS amp EQUIPMENT Used in Figures calls out the specific tools and equipment recommended for this process. II REVISION MARK This mark highlights a change in installation with respect to previous issue. Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure quality...
A Xij
1 Tie the wire harness and vehicle harness at their branch points so that they are secured in a bundle with a plastic tie 150 mm . 2 Secure wire harness to vehicle harness with a plastic tie 150mm as shown. Fig. 4-1 1 Connect the wire harness 10P to the converter 10P . Fig. 4-2 1 Secure the wire harness to the vehicle harness with two plastic ties 150mm . Fig. 4-3 1 Route the wire harness as shown. e Route the wire harness to the vehicle harness, fasten the wire harness ground terminal to the...
Info Jjw
p From the engine compartment, lightly pull the vehicle harness, and fit the grommet into the bulkhead of the engine compartment. Fig. 3-12 1 Verify the grommet is installed properly. If the grommet does not fit into the firewall, then water will come into the passenger compartment. q Secure the hood switch harness to the vehicle harness with one wire tie in the engine compartment area. Fig. 3-13 r Locate the RES harness' white 2P connector in the glove box area, then disconnect the white male...
Radar Sensor Off Mode
THE RADAR SENSOR CAN BE DEACTIVATED. PERFORM THE FOLLOWING The LED turns off. The system is now DISARMED. 2. Lock, then unlock the driver's door inside lock button 3 times, within 5 seconds. 4. ARM the system with the remote control or key while the LED is blinking.THE RADAR SENSOR will deactivate during arming. NOTE If you disarm the system after you set the radar sensor OFF, you have to repeat the above procedure when you arm the system if you want to deactivate the radar sensor again. the...
Remove Oil Filter Cap Assembly
a Connect the hose to a pipe. HINT The drain pipe is supplied with the oil filter element. b Remove the oil filter drain plug and O-ring, and then insert the drain pipe into the oil filter cap and drain the engine oil into a container. c Make sure that oil is completely drained, and remove the pipe and O-ring. HINT Be sure to turn the pipe in the direction of the arrow to remove it. d Using SST, remove the oil filter cap together with the oil filter element. SST 09228-06501 a Remove the oil...
A Pat
r Plug in the RES harness' white 8P connectors between the vehicle harness' 8P connector and the ignition switch. Fig. 2-10 1 Verify the connectors are plugged in securely. s Secure the 8P connector to the vehicle harness with one wire tie. Fig. 2-10 CAUTION Position the 8P connector exactly as shown. Otherwise, when other vehicle parts are placed, serious damage may occur to the vehicle parts or accessories. 1 Do not secure the air bag harness yellow connector wires . 2 After securing the...
Nbey Sdz
The point at which the air bubbles disappear in the refrigerant of the sub-cool cycle is lower than the proper amount of refrigerant with which the system must be filled. Therefore, if the system is recharged with refrigerant based on the point at which the air bubbles disappear, the amount of refrigerant would be insufficient. As a result, the cooling performance of the system will be affected. If the system is overcharged with refrigerant, this will also lead to a reduced performance. For the...
Be Yom
This pulley contains a damper to absorb the torque fluctuations of the engine and a limiter mechanism to protect the drive belt in case the compressor locks. In the event that the compressor locks, the limiter mechanism causes the spoke portion of the pulley to break, thus separating the pulley from the compressor. To reduce weight, the pulley portion is made of plastic.
Be Stf
A clean air filter high efficiency type is used to remove dust, pollen, and other micron particles from air entering from outside the vehicle to provide a comfortable cabin of clean air. The clean air filter is installed in the upper section of the blower fan for easy replacement of the clean air filter without the need for tools by removing the one-touch clip in the glove box, making this easy to service. The clean air filter on the U.S.A models should be changed at 30,000 miles. On the Canada...
Operation 1
DISARMING THE RS3200 Plus except PASSIVE DISARMING The system may be Disarmed in several ways. Do one of the following Insert the key into the door key switch and turn it toward the rear of the vehicle The Status Monitor's LED stops flashing. The system is now Disarmed. Unlock the doors with the remote control Press the unlock button on the remote control. Simultaneously The drivers door unlocks. The vehicle's tail and marker or turn signal lights flash twice. The vehicle's buzzer chirps twice....