Torque Specifications Jrr
Steering wheel assembly x Steering column assembly Steering sliding yoke sub-assembly x Steering gear assembly Steering intermediate shaft assembly No. 2 x Steering column assembly Steering column x Instrument panel reinforcement assembly
Front Speed Sensor
Front speed sensor clamp Flexible hose clamp x Flexible hose bracket Front speed sensor clamp x Side member
Suspension Service Data
0 05' -10' 0.08 -0.16 1.0 -2.0 mm 0.04 -0.08 in. 0 11' -10' 0.18 -0.17 2.3 -1 mm 0.09 -0.04 in. 0 55' -45' -0.92 -0.75 45' 0.75 or less -1 04' -45' -1.07 -0.75 45' 0.75 or less -0 52' -45' -0.87 -0.75 45' 0.75 or less 0.98 to 3.43 N m 10 to 35 kgf cm, 9 to 30 in. lbf or less 0.05 to 1.96 N m, 0.5 to 20 kgf cm, 0.4 to 17 in. lbf or less 0.05 to 1.96 N m, 0.5 to 20 kgf cm, 0.4 to 17 in. lbf or less
Knock Sensor Components 1
INTAKE AIR SURGE TANK TO INTAKE MANIFOLD GASKET NO. 1 INTAKE MANIFOLD TO HEAD GASKET N m kgf cm, ft. lbf Specified torque INTAKE AIR SURGE TANK TO INTAKE MANIFOLD GASKET THROTTLE BODY BRACKET WITH VACUUM HOSE CLAMP NO. 1 INTAKE MANIFOLD TO HEAD GASKET N m kgf cm, ft. lbf Specified torque 1 Do not allow oil to contact these bolts
Circuit Opening Relay Onvehicle Inspection 1
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Wait at least 90 seconds after disconnecting the cable from the negative - battery terminal to prevent airbag and seat belt pretensioner activation. 2. INSPECT INSTRUMENT PANEL JUNCTION BLOCK NOTICE The circuit opening C OPN relay is built into the instrument panel junction block. a Measure the resistance between the terminals. Instrument Panel Junction Block Front View
Onvehicle Inspection Iea
4. INSPECT AIR CLEANER FILTER ELEMENT SUBASSEMBLY a Remove the air cleaner cap. b Remove the air filter element. c Visually check that the air filter is not excessively damaged or oily. If necessary, replace the air filter. 6. INSPECT FAN AND GENERATOR V BELT You do not need to check the belt deflection because the auto tensioner has been adopted. 7. INSPECT IGNITION TIMING NOTICE Turn all the electrical systems and the A C OFF. Inspect the ignition timing with the cooling fan OFF. When...
Fuel Pump Relay Onvehicle Inspection
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Wait at least 90 seconds after disconnecting the cable from the negative - battery terminal to prevent airbag and seat belt pretensioner activation. a Remove the fuel pump relay from the engine room No. 1 relay block. a Measure the resistance of the fuel pump relay. Standard resistance when battery voltage is applied to terminals 1 and 2 when battery voltage is applied to terminals 1 and 2 If the result is not as specified, replace the relay....
INSPECT TRANSFER OIL for WD
a Visually check the transfer for oil leakage. If oil is leaking, find the cause and repair it. 6. INSPECT REAR DIFFERENTIAL OIL for 4WD a For the rear differential oil inspection, refer to the following procedures see page DF-3 . 7. ROTATE TIRES See page TW-1
Onvehicle Inspection Tkh
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Wait at least 90 seconds after disconnecting the cable from the negative - battery terminal to prevent airbag and seat belt pretensioner activation. a Remove the IG1 relay from the instrument panel junction block. a Measure the resistance of the IG1 relay. Standard resistance when battery voltage is applied to terminals 1 and 2 If the result is not as specified, replace the relay. 5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Camshaft Timing Oil Control Valve Assembly Components 1
CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY THROTTLE BODY BRACKET WITH VACUUM HOSE CLAMP THROTTLE BODY BRACKET WITH VACUUM HOSE CLAMP INTAKE AIR SURGE TANK TO INTAKE MANIFOLD GASKET INTAKE AIR SURGE TANK TO INTAKE MANIFOLD GASKET CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY N m kgf cm, ft. lbf Specified torque CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY N m kgf cm, ft. lbf Specified torque CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY 2GR-FE ENGINE CONTROL...