and note locations Arrange parts in order for reassembly reference
Remove detent spring and manual valve from valve body assembly. Remove solenoids and lock plate if applicable , oil strainer and pressure relief valve. Remove lower valve body-to-upper valve body bolts. Note bolt length and location. Separate upper valve body and valve body plate from lower valve body. See Fig. 49 or Fig. 50 . Fig. 49 Exploded View Of A340 Series Control Valve Assembly Except Sequoia amp Tundra V8 Courtesy of TOYOTA MOTOR SALES, U.S.A. INC. Fig. 49 Exploded View Of A340 Series...
Install Main Shaft Assembly
a. Install the inner race, upper bearing inner race seat, compression spring and spring retainer. b. Install a new No. 2 steering column ring to the main shaft assembly. c. Install the washer of SST on the main shaft assembly. 2004 STEERING Tilt Steering Column - Sequoia d. Set SST on the main shaft assembly, as shown in the illustration. e. Using SST, push down the retaining ring until it fits into the shaft groove and install the main shaft assembly.
NOTE When replacing the ECU perform the zero point calibration See PRECHECK
DTC C1310 11 ACTIVE BRAKE BOOSTER SOLENOID CIRCUIT CIRCUIT DESCRIPTION Open or short in active brake booster solenoid circuit. Active brake booster solenoid circuit Fig. 70 DTC C1310 11 Detecting Condition Trouble Area Table Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2004 BRAKES ABS With EBD amp BA amp TRAC amp VSC System - Diagnostics - Sequoia Fig. 71 Wiring Diagram - Active Brake Booster Solenoid Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 71 Wiring Diagram - Active Brake Booster...
Remove Fuel Pump Filter From Fuel Pump
a. Using a small screwdriver, remove the clip. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. INSPECTION Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. INSPECTION Using an ohmmeter, measure the resistance between the terminals. Resistance 0.2 - 3.0 ohm at 20 C 68 F If the resistance is not as specified, replace the fuel pump. Fig. 23 Measuring Resistance Between Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 23 Measuring Resistance Between Terminals Courtesy of TOYOTA MOTOR SALES,...
Nd Coast Brake Band
Compress spring and remove E ring from piston rod. Remove 2nd coast brake servo piston, spring and retainer from piston rod. Remove oil seal ring. 1. Replace brake band if lining is peeled off or discolored or printed numbers are defaced. Before assembling NEW band, soak band in ATF for at least 15 minutes. 2. If brake band is serviceable but piston rod stroke is not within specification, select replacement rod. Rods are available in lengths of 2.78 70.7 mm , 2.81 71.4 mm , 2.84 72.2 mm , 2.87...
NOTE The thermostat is numbered with the valve opening temperature
Fig. 3 Identifying Thermostat Opening Temperature Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 3 Identifying Thermostat Opening Temperature Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Immerse the thermostat in water and gradually heat the water. b. Check the valve opening temperature. Fig. 4 Checking Valve Opening Temperature Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Valve opening temperature 80 - 84 C 176 - 183 F If the valve opening temperature is not as specified, replace the...
NOTE During testing if DTCs other than DTC B are displayed disregard them Psu
1. Disable air bag system. See DISABLING SYSTEM under DISABLING amp ACTIVATING AIR BAG SYSTEM. 2004 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems 2. Measure resistance between ground and Yellow Black wire circuit PL of air bag sensor assembly side of driver-side seat belt pretensioner squib harness connector. See WIRING DIAGRAMS . If resistance is less than one megohm, repair or replace harness or connector between seat belt pretensioner and air bag sensor assembly. If...
NOTE Do not turn the crankshaft pulley
Fig. 13 Removing Crankshaft Pulley Bolt Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 14 Removing Timing Belt Tensioner Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. NOTE When re-using timing belt If the installation marks have disappeared, before remove the timing belt, place 2 new installation marks on the timing belt to match the timing marks of the camshaft timing pulleys. When replacing timing belt tensioner only To avoid meshing of the timing pulley and timing belt, secure one of them...
Remove Steering Column Assembly With No Universal Joint Assembly
b. Remove the 4 steering column set nuts. c. Pull out the steering column assembly with No. 2 universal joint assembly connected. 2004 STEERING Tilt Steering Column - Sequoia Fig. 8 Disconnecting Transmission Control Cable Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 8 Disconnecting Transmission Control Cable Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
If a malfunction code is displayed during the DTC check check the circuit
DIAGNOSTIC TROUBLE CODES CHART OF ABS SYSTEM Right front wheel speed sensor signal malfunction Right front, fett front, right rear and left rear speed sensor Left front wheel speed sensor signal malfunction Right rear wheel speed sensor signal malfunction Left rear wheel speed sensor signal malfunction Malfunction in ABS amp VSC solenoid valves ABS amp VSC actuator ABS amp VSC solenoid circuit Open or short circuit In ABS amp VSC relay drcuil ABS a VSC solenoid relay ABS amp VSC solenoid relay...
Toyota Sequoia Limited Jjz
2004 ACCESSORIES amp EQUIPMENT Air Conditioning System - Diagnostics - Sequoia Front air mix damper position sensor circuit Front air mix damper position sensor Harness or connector between fronI air mix damper position sonscr and integration control and panot Integration control and panel Air inlet damper position sensor circuit Air inlet damper position sensor Harness or connector between air inlet damper position sensor and integration control and panel Integration control and panel Water...
CAUTION Do not suck air through the valve Petroleum substances inside the valve
Fig. 3 Inspecting PCV Valve Operation Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 3 Inspecting PCV Valve Operation Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2. Blow air into the intake manifold side, and check that air passes through with difficulty. If operation is not as specified, replace the PCV valve. d. Remove the clean hose from the PCV valve. 2004 ENGINE PERFORMANCE Emission Control System - Sequoia Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES,...
Front Planetary Gear
Remove thrust bearings and races from planetary gear and front planetary ring gear. Note direction of race installation. Measure front planetary ring gear bushing inside diameter. Replace planetary ring gear if bushing diameter exceeds .948 24.08 mm . Measure planetary pinion gear thrust clearance. Clearance should be .008.024 .20-.61 mm . Maximum clearance is .039 1.00 mm . If clearance is not within specifications, replace planetary gear assembly. Coat thrust bearings and races with petroleum...
NOTE Take care not to scratch the serration of the speed sensor rotor Dma
5. On 2WD models, install new lock nut. Using Special Tool 09318-12010 , install and torque a new lock nut to the axle hub. See Fig. 3 . Torque to specification. See TORQUE SPECIFICATIONS . Using a chisel and hammer, stake the lock nut. 6. On 4WD models, install bearing spacer. Using Special Tool 09950-60010, 09951-00650, 09950-70010, 09951-07150 and a press, install the bearing spacer. See Fig. 1 and Fig. 3 . 7. On 2WD models, install grease cap. See Fig. 3 . 8. On 4WD models, install new oil...
Volume cm cu in per second Difference between each injector cm cu in or less
If the injection volume is not as specified, replace the injector. Fig. 43 Connecting SST Wire To Injector And Battery Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 43 Connecting SST Wire To Injector And Battery Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. In the condition above, disconnect the tester probes of SST wire from the battery and check the fuel leakage from the injector. Fuel drop 1 drop or less per 12 minutes b. Turn the ignition switch OFF. c. Disconnect the negative -...
DISCONNECT AC COMPRESSOR FROM ENGINE See REMOVAL
Fig. 8 Removing No. 2 Timing Belt Cover Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Remove the 2 bolts, 2 nuts and fan bracket. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 14. IF RE-USING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks on the timing belt by turning the crankshaft pulley as shown in the illustration.
Antitheft
2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia 2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia Fig. 6 Forced Entry Circuit 1 of 3 2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia 2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia Fig. 7 Forced Entry Circuit 2 of 3 2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia 2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia Fig. 8 Forced Entry Circuit 3 of 3 2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia 2004 SYSTEM WIRING DIAGRAMS Toyota - Sequoia
P Leg
Fig. 36 Measuring Side Gear Backlash Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 3. INSTALL STRAIGHT PIN AND STAKE DIFFERENTIAL CASE a. Using a pin punch and hammer, install the straight pin through the differential case and hole in the pinion shaft. b. Stake the differential case. 4. INSTALL RING GEAR ON DIFFERENTIAL CASE a. Clean the contact surfaces of the differential case and ring gear. 2004 DRIVELINE AXLES Front Differential Carrier - Sequoia Fig. 37 Installing Straight Pin amp Stake...
Install Vehicle Speed Sensor Drive Gear And Output Shaft Washer
a. Install the ball on the rear output shaft. b. Install the vehicle speed sensor drive gear and 2 output shaft washers. 2004 Transmission Transfer - Sequoia Fig. 58 Installing Shift Head No. 2 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Apply FIPG to the extension housing, as shown. Part No. 08826-00090, THREE BOND 1281 or equivalent b. Apply sealant to the bolt threads. Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent c. Install the extension housing with the 5 bolts....
Inspect System Operation
a. Inspect the throttle control motor for operating sound. 1. Turn the ignition switch ON. 2. When depress the accelerator pedal, check the running sound of the motor. Also, check that there is no friction sound. If operation is not as specified, check the throttle control motor See 3 , wiring and ECM. Fig. 59 Inspecting Throttle Control Motor For Operating Sound Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 59 Inspecting Throttle Control Motor For Operating Sound Courtesy of TOYOTA MOTOR...
Torque Specifications Mlx
1 Replace with NEW nuts on reassembly. 2 Replace with NEW bolts on reassembly.
Nd Brake
Remove thrust washer. Using appropriate compressor, compress piston return spring with an arbor press. Remove snap ring. Remove spring retainer and piston return spring. Hold 2nd brake piston and apply compressed air to 2nd brake drum to remove piston. Check all parts for wear and damage. Soak NEW discs in ATF for 15 minutes before installation. Measure return spring free length. Free length should be .654 16.61 mm . Replace components as necessary. Coat NEW O rings with ATF and install....
NOTE Perform this procedure only if you were sent here from DIAGNOSTIC TESTS
1. Air bag squib circuit consists of circuit between air bag sensor assembly and air bag. If voltage is accidentally applied across squib circuit as when testing, for example , air bag will deploy. 2. To prevent accidental deployment, squib circuit connectors contain a spring-loaded shorting bar shorting spring . When squib circuit connector is disconnected, shorting spring automatically shorts squib circuit positive and negative circuits together. This prevents air bag deployment if voltage is...
Standard throttle valve opening percentage or more
If operation is not as specified, check that the accelerator pedal position sensor See DTC P2120 THROTTLE PEDAL POSITION SENSOR SWITCH , wiring and ECM. Fig. 60 Connecting Hand-Held Tester To DLC3 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 60 Connecting Hand-Held Tester To DLC3 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. If you have no TOYOTA hand-held tester, measure voltage between terminals VTA and E2 of the ECM connector See DTC P0120 THROTTLE PEDAL POSITION SENSOR SWITCH . 1. Start...
NOTE Do not rotate the fuel filter outlet when tightening the flare nut
28 N.m 285 kgf.cm, 21 ft.lbf for use with SST 34.3 N.m 350 kgf.cm, 25 ft.lbf NOTE Use a torque wrench with a fulcrum length of 30 cm 11.81 in. . Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. d. Observe these precautions when removing and installing the injectors. 2. When placing a new O-ring on the injector, take care not to damage it in any way. 3. Coat a new O-ring with spindle oil or gasoline before installing-never use engine, gear or brake oil. Fig. 7 Identifying Correct Way Of Installing...
CAUTION Install a suitable vinyl hose onto the injector to prevent gasoline
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. j. Connect a TOYOTA hand-held tester to the DLC3. k. Connect the battery negative - cable to the battery. l. Turn the ignition switch ON, and push the TOYOTA hand-held tester main switch ON. Fig. 42 Connecting Hand-Held Tester To DLC3 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 42 Connecting Hand-Held Tester To DLC3 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
When overhauling caliper if piston bores are pitted or scored beyond repair by
For removal and installation procedure, see FRONT BRAKE CALIPER under REMOVAL amp INSTALLATION. For overhaul procedure, see Fig. 21 . For component view, see Fig. 22 . Fig. 21 Front Brake Caliper Overhaul Procedure Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 21 Front Brake Caliper Overhaul Procedure Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 22 Locating Front Brake Caliper Components Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 22 Locating Front Brake Caliper Components...
Inspect Efi Main Relay Continuity
a. Using an ohmmeter, check that there is continuity between terminals 1 and 2. If there is no continuity, replace the relay. b. Check that there is no continuity between terminals 3 and 5. If there is continuity, replace the relay. Fig. 69 Checking Continuity Between Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 69 Checking Continuity Between Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Apply battery voltage across terminals 1 and 2. b. Using an ohmmeter, check that...
Circuit Inspection
2004 BRAKES ABS With EBD amp BA amp TRAC amp VSC System - Diagnostics - Sequoia DTC C0200 31, C0205 32, C0210 33, C0215 34 SPEED SENSOR CIRCUIT CIRCUIT DESCRIPTION The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the ABS control system. The front and rear rotors each have 48 serrations. When the rotors rotate, the magnetic field emitted by the permanent magnet in the speed sensor generates an AC voltage. Since the frequency of...
NOTE When replacing the skid control ECU perform zero point calibration See
Replace brake booster VACUUM BRAKE BOOSTER . DTC C1249 49 STOP LIGHT SWITCH CIRCUIT CIRCUIT DESCRIPTION ECU terminal STP voltage is low when both ignition switch and stop light switch are ON. Stop light switch Slop light switch circuit Fig. 66 DTC C1249 49 Detecting Condition Trouble Area Table Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2004 BRAKES ABS With EBD amp BA amp TRAC amp VSC System - Diagnostics - Sequoia Fig. 67 Wiring Diagram - Stop Light Switch Courtesy of TOYOTA MOTOR SALES,...
DTC No C is for the left front speed sensor DTC No C is for the right rear
2004 BRAKES ABS With EBD amp BA amp TRAC amp VSC System - Diagnostics - Sequoia Fig. 30 Wiring Diagram Speed Sensor Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 30 Wiring Diagram Speed Sensor Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. NOTE Start the inspection from step 1 in the case of using the TOYOTA hand-held tester and start from step 2 in the case of not using TOYOTA hand-held tester. 1. Check output value of speed sensor. PREPARATION a. Connect the TOYOTA hand-held tester to the...
Oil Pump Clearance Specifications
1. Install oil seal until seal is even with outer edge of pump housing. Place stator shaft in torque converter while working on pump. Coat all components with ATF. See Fig. 26. 2. Align reference marks on gears during installation. To complete reassembly, reverse disassembly procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS. DO NOT over expand seal rings during installation. Ensure seal rings move smoothly after installation. Ensure drive gear rotates smoothly when installed...
Do not start the engine 1
c. Select the ACTIVE TEST mode on the TOYOTA hand-held tester. d. Please refer to the TOYOTA hand-held tester operator's manual for further details. Fig. 15 Connecting Toyota Hand-Held Tester To DLC3 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 15 Connecting Toyota Hand-Held Tester To DLC3 Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. e. Check that the pulsation damper screw rises up when the fuel pump operates. If operation is not as specified, check the fusible link, fuses, EFI main...
CAUTION System may be damaged if jumper wire is incorrectly connected across
1. To check for past codes, go to next step. To check for present codes, turn ignition switch to ON position. Wait about 20 seconds. Using Diagnosis Check Wire 09843-18040 , connect terminals Tc and CG of Data Link Connector DLC3 . See Fig. 20 . DLC3 is located under left side of instrument panel. Go to step 3 . 2. To check for past codes, connect Diagnosis Check Wire 09843-18040 to terminals Tc and CG of Data Link Connector DLC3 . See Fig. 20 . Turn ignition switch to ON position. Wait about...
NOTE When replacing the skid control ECU perform the zero point calibration See
3. Check for open circuit in harness and connector between skid control ECU and stop light switch See HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE . NG Repair or replace harness or connector. OK Proceed to next circuit inspection shown on problem symptoms table See PROBLEM SYMPTOMS TABLE . DTC C1251 51 ABS amp VSC PUMP MOTOR LOCK CIRCUIT DESCRIPTION DIAGNOSTIC TROUBLE CODES C1251 51 DETECTING CONDIT Pump motor does not operate during the initial check. 2004 BRAKES ABS With EBD amp...
Overdrive Support Brake
Remove all thrust washers from overdrive support. Using appropriate compressor, compress piston return spring and remove snap ring. Place support on direct clutch assembly. Hold brake piston in a level position. Carefully apply air pressure to piston supply port and remove piston. Remove oil seal rings from rear of support. See Fig. 39. Clean all components with solvent. Dry with compressed air. Inspect components for damage. Measure return spring free length. Free length should be .702 17.82...
Belt Adjustment
Serpentine belt uses an automatic belt tensioner, so no adjustment is necessary, but serpentine drive belt must be properly installed. See Fig. 1 . 1 Automatic belt tensioner is used. Adjustment is not required.
G Ohe
Fig. 37 Cylinder End Turning Stopper Clockwise Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Install SST to the rack housing. b. Apply 53 kPa 400 mmHg, 15.75 in.Hg of vacuum for about 30 seconds. c. Check that there is no change in the vacuum. If there is change in the vacuum, check the installation of the oil seals. 2004 STEERING Power Steering Gear - Sequoia Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. To prevent oil seal lip damage, wind vinyl tape on the serrated part of the valve...
NOTE When replacing the master cylinder pressure sensor perform the zero point
NG Go to next step. 5. Check yaw rate and deceleration sensor. 2004 BRAKES ABS With EBD amp BA amp TRAC amp VSC System - Diagnostics - Sequoia Disconnect the connector from the yaw rate and deceleration sensor. CHECK a. Turn the ignition switch ON. b. Measure voltage between terminal VYS and GYAW of skid control ECU. Fig. 86 Identifying Yaw Rate amp Deceleration Sensor Connector Terminals VYS amp GYAW Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 86 Identifying Yaw Rate amp Deceleration...
NOTE If a DTC other than DTC B is displayed at same time as DTC B repair fault
1. Disable air bag system. See DISABLING SYSTEM under DISABLING amp ACTIVATING AIR BAG SYSTEM. Reconnect negative battery cable. 2. Turn ignition switch to ON position. Measure voltage between ground and air bag sensor assembly connector A20, terminal No. 5 circuit IG2, Black Orange wire . See Fig. 22 . Measure voltage between ground and air bag sensor assembly connector A20, terminal No. 6 circuit IG1, Black Red wire . If voltage in both tests is 10-14 volts, go to next step. If either voltage...
OD PLANETARY GEAR OD DIRECT CLUTCH OD ONEWAY CLUTCH Disassembly
1. One-way clutch operation should be checked prior to disassembly. Hold clutch drum and rotate input shaft clockwise. See Fig. 30. Input shaft should rotate freely clockwise and lock counterclockwise. 2. Remove clutch drum from planetary gear. Remove thrust bearing from clutch drum. Remove snap ring, flange, discs and plates from clutch drum. Note number and location of components. 3. Using appropriate compressor, compress piston return spring and remove snap ring. Carefully release press and...
Dtc B Open In Right Side Head Impact Air Bag Module Squib Circuit
The right side head impact air bag module squib circuit consists of the air bag sensor assembly and right side 2004 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems head impact air bag module. The squib circuit causes the right side head impact air bag module to deploy when deployment conditions are satisfied. DTC 84 B1161 could be caused by an open in Yellow Violet circuit ICR and Yellow Orange circuit ICR- wires in right side head impact air bag module squib circuit, right side...
NOTE During testing if DTCs other than DTC B are displayed disregard them Yrf
1. Disable air bag system. See DISABLING SYSTEM under DISABLING amp ACTIVATING AIR BAG SYSTEM. 2. Measure resistance between Yellow Red wire circuit P and Yellow Green wire circuit P- on air bag sensor assembly side of passenger-side air bag module harness connector. See WIRING DIAGRAMS . If resistance is less than one ohm, go to next step. If resistance is more than one ohm, repair or replace harness or connector between passenger-side air bag module harness connector and air bag sensor...
Vsv For Evaporative Emission Evap
Fig. 79 Identifying VSV For Evaporative Emission EVAP Components Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Inspect the VSV for open circuit. Using an ohmmeter, check that there is continuity between the terminals. Resistance 30 - 34 ohm at 20 C 68 F If there is no continuity, replace the VSV. Fig. 80 Checking Continuity Between Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 80 Checking Continuity Between Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Using an...
Dtc B Open In Passengerside Air Bag Module Squib Circuit
The passenger-side air bag squib circuit consists of the air bag sensor assembly and passenger-side air bag module. The squib circuit causes the passenger-side air bag to deploy when deployment conditions are satisfied. DTC 54 B0106 could be caused by an open in Yellow Red circuit P and Yellow Green circuit P- wires in passenger-side air bag squib circuit, passenger-side air bag squib malfunction or air bag sensor assembly malfunction.
Fig AC System Problem Symptoms Table Front AC Of Courtesy of TOYOTA MOTOR SALES
2004 ACCESSORIES amp EQUIPMENT Air Conditioning System - Diagnostics - Sequoia Temperature Control No temperature control only Max cool or Max. warm 1 Front room temp, sensor circuit 7. Amhlent temp sensor circuit 3. Front air mix damper position sensor circuit 4. Front air mix damper control servomotor circuit 5. Integration control and panel 1. Front air Inlet damper position sensor circuit 2. Front air inlet damper control servomotor circuit 3. Integration control and panel 1 Air outlet...
Remove Front Propeller Shaft
a. Place matchmarks on the differential and propeller shaft flange. b. Remove the 4 nuts, washers and bolts, disconnect the propeller shaft from the differential. 2004 DRIVELINE AXLES Propeller Shaft - Sequoia c. Suspend the front side of the propeller shaft. d. Place matchmarks on the transfer and propeller shaft flanges. e. Remove the 4 nuts and washers. f. Remove the propeller shaft from the transfer.
Dtc B Short In Left Side Air Bag Module Squib Circuit
The side air bag module squib circuit consists of the air bag sensor assembly and side air bag module. The squib circuit causes the side air bag to deploy when deployment conditions are satisfied. DTC 47 B0115 could be caused by a short between Yellow Red circuit SFL and Yellow Green circuit SFL- 2004 ACCESSORIES SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems wires in side air bag squib circuit, side air bag squib malfunction or air bag sensor assembly malfunction.
G Vxi
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Align the installation hole for the wire of the stopper with the slot of the rack housing. b. Install a new wire into the stopper. c. Using SST, turn the stopper clockwise 450 - 50 . 2004 STEERING Power Steering Gear - Sequoia