Check Side Airbag Sensor Lh
a. Connect the connectors to the center airbag sensor assembly. b. Interchange the side airbag sensor RH with LH and connect the connectors to them. c. Connect the negative - terminal cable to the battery, and wait for at least 2 seconds. d. Turn the ignition switch to the ON position, and wait for at least 60 seconds. e. Clear the DTCs stored in memory See DTC CHECK CLEAR . f. Turn the ignition switch to the LOCK position. g. Turn the ignition switch to the ON position, and wait for at least...
Check Front Airbag Sensor Rh
a. Connect the connectors to the center airbag sensor assembly. b. Interchange the front airbag sensor RH with LH and connect the connectors to them. c. Connect the negative - terminal cable to the battery, and wait for at least 2 seconds. d. Turn the ignition switch to the ON position, and wait for at least 60 seconds. e. Clear the DTCs stored in memory See DTC CHECK CLEAR . f. Turn the ignition switch to the LOCK position. g. Turn the ignition switch to the ON position, and wait for at least...
Rear Axle Shaft
Fig. 23 Identifying Rear Axle Shaft Components Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 23 Identifying Rear Axle Shaft Components Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Using a dial indicator, check the backlash in the bearing shaft direction. If the backlash exceeds the maximum, replace the bearing. b. Using a dial indicator, check the deviation at the surface of the axle shaft outside the hub bolt. Maximum 0.1 mm 0.0040 in. If the deviation exceeds the maximum, replace the...
Remove Front Differential Tube Assembly
a. Using a Torx socket E14 , remove the 4 Torx bolts. b. Using a plastic hammer, tap on the differential tube to remove it. d. Remove the O-ring from the differential tube. 2007 DRIVELINE AXLES Differential - Sequoia Fig. 35 Removing Front Differential Tube Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 35 Removing Front Differential Tube Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Ok Hay
DTC B1610 13 and B1615 14 are not output. Codes other than DTC B1610 13 and B1615 14 may be output at this time, but they are not related to this check. 2007 RESTRAINTS Supplemental Restraint System - Sequoia Fig. 73 Identifying DLC3 Connector Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 73 Identifying DLC3 Connector Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2007 RESTRAINTS Supplemental Restraint System - Sequoia
Dtc C Right Front Wheel Speed Sensor Signal Dtc C Left Front Wheel Speed Sensor
Fig. 35 Right Front Wheel Speed Sensor Signal - System Description Fig. 35 Right Front Wheel Speed Sensor Signal - System Description The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the ABS control system. The front and rear rotors have 48 serrations each. When the rotors rotate, the magnetic field emitted by the permanent magnet in the speed sensor generates AC voltage. Since the frequency of this AC voltage changes in direct...
OK DTC B is not output Gpp
Codes other than DTC B1620 21 may be output at this time, but they are not related to this check. NG Go to step 2 2007 RESTRAINTS Supplemental Restraint System - Sequoia Fig. 79 Identifying DLC3 Connector Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 79 Identifying DLC3 Connector Terminals Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2007 RESTRAINTS Supplemental Restraint System - Sequoia
Diagnostic Trouble Code Chart Tqv
DTC B1620 21 and B1625 22 are not output. 2007 RESTRAINTS Supplemental Restraint System - Sequoia Codes other than DTC B1620 21 and B1625 22 may be output at this time, but they are not related to this check. A REPLACE CENTER AIRBAG SENSOR ASSEMBLY B REPLACE SIDE AIRBAG SENSOR LH C USE SIMULATION METHOD TO CHECK DTC B1630 23 REAR AIRBAG SENSOR RH CIRCUIT MALFUNCTION DESCRIPTION The rear airbag sensor RH consists of the safing sensor the diagnostic circuit, the lateral deceleration sensor, etc....
Fig Knock Sensor Waveform Graph WAVEFORM
Camshaft timing oil control valve OCV WAVEFORM REFERENCE CHART Camshaft timing oil control valve OCV WAVEFORM REFERENCE CHART Between OC1 and OC1-Between OC2 and OC2- Accelerate slowly after engine warmed-up In the DATA LIST, the items VVT OCV DUTY B1 and B2 show the duty ratio of voltage flowing to the OCV see illustration . 2007 ENGINE PERFORMANCE Engine Control System 2UZ-FE - Sequoia Fig. 17 Camshaft Timing Oil Control Valve Waveform Graph OCV 4. WAVEFORM 4 Fig. 17 Camshaft Timing Oil...
Install Front Drive Pinion Companion Flange Subassembly
a. Place the companion flange on the drive pinion. b. Coat the threads of a new nut with hypoid gear oil. c. Using SST to hold the flange, torque the nut. 2007 DRIVELINE AXLES Differential - Sequoia Fig. 82 Installing Front Drive Pinion Companion Flange Sub-Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 82 Installing Front Drive Pinion Companion Flange Sub-Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Torque 108 N m 1,100 kgf cm, 80 ft. lbf a. Using a torque wrench, measure...
Continuity Reference
b. Apply battery positive voltage between terminals 1 and 2. c. Check continuity between terminals. Fig. 72 Inspecting Inhibit Relay OK GO TO Next Step 3. CHECK HARNESS AND CONNECTOR INHIBIT RELAY - SKID CONTROL ECU NG REPAIR OR REPLACE HARNESS OR CONNECTOR OK REPLACE SKID CONTROL ECU DTC C1337 37 DIFFERENT DIAMETER TIRE MALFUNCTION Skid control ECU measure the speed of each wheel by receiving signals from speed sensor. These signals are used for recognizing all 4 wheels are operating properly....
Ok Replace Center Airbag Sensor Assembly Dtc B Passenger Side Buckle Switch
The passenger side buckle switch circuit consists of the occupant classification ECU and the front seat inner belt RH. DTC B1771 is recorded when a malfunction is detected in the passenger side buckle switch circuit. Troubleshoot DTC B1771 first when the DTC B1771 and B1795 are output simultaneously. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B signal in the passenger side buckle switch...
Remove Air Injection Control Driver
a. Disconnect the 2 connectors from the air injection control driver. b. Remove the 2 bolts and air injection control driver from the body. 2007 ENGINE Emission Control - Sequoia Fig. 26 Removing Bolts amp Air Injection Control Driver From Body Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 26 Removing Bolts amp Air Injection Control Driver From Body Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Ok Replace Skid Control Ecu Trac Off Indicator Light Trac Off Switch Circuit
This is the TRAC control main switch. When the TRAC OFF switch is pushed on, TRAC indicator goes off and the TRAC OFF indicator comes on. Turn the ignition witch OFF, and check that the TRAC indicator comes on when turning the ignition switch to the ON position again. Fig. 88 TRAC OFF Indicator Light, TRAC OFF Switch - Wiring Diagram Fig. 88 TRAC OFF Indicator Light, TRAC OFF Switch - Wiring Diagram
Replace Steering Wheel Pad Driver Side Squib
a. Replace the steering wheel pad See STEERING PAD . Perform the inspection using parts from a normal vehicle if possible. b. Connect the connectors to the center airbag sensor assembly. c. Connect the negative - terminal cable to the battery, and wait for at least 2 seconds. d. Turn the ignition switch to the ON position, and wait for at least 60 seconds. e. Clear the DTCs stored in memory See DTC CHECK CLEAR . f. Turn the ignition switch to the LOCK position. g. Turn the ignition switch to...
Check Dtc Evg
a. Connect the connectors to the occupant classification ECU and the occupant classification sensor rear LH. b. Connect the negative - terminal cable to the battery. c. Turn the ignition switch to the ON position. d. Clear the DTCs stored in memory See DTC CHECK CLEAR . First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly. e. Turn the ignition switch to the LOCK position. f. Turn the ignition switch to the ON position. g. Using the intelligent...
Check Seat Wire No To B Jfh
a. Disconnect the connector from the occupant classification ECU and the 4 occupant classification sensors. b. Connect the negative - terminal cable to the battery. c. Turn the ignition switch to the ON position. d. Measure the voltage according to the value s in the table below. 2007 RESTRAINTS Supplemental Restraint System - Sequoia Fig. 187 Checking Seat Wire No.1 To B Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 187 Checking Seat Wire No.1 To B Courtesy of TOYOTA MOTOR SALES, U.S.A.,...
A Replace Four Wheel Drive Control Ecu Dtc C Malfunction In Comparative Master
The master cylinder pressure sensors are connected to the skid control ECU. Attached to the master cylinder one reads front master cylinder pressure and the other reads rear master cylinder pressure. When any of the following conditions are detected 1. Noise to ECU terminal PMC occurs. 2. While ECU terminal STP is OFF, ECU terminal PMC voltage is out of standard range. 3. When ECU terminal IG1 voltage is proper, ECU terminal VCM voltage is out of range. 4. When ECU terminal VCM voltage is...
Vacuum Switching Valve
2007 ENGINE Emission Control - Sequoia N m kgf'cm. ft. lbf Specified torque Fig. 49 Identifying Vacuum Switching Valve Components With Specified Torque Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 1. REMOVE VACUUM SWITCHING VALVE 2. INSPECT VACUUM SWITCHING VALVE a. Inspect the VSV for open circuit. Using an ohmmeter, check that there is continuity between the terminals. Resistance 30 to 34 ohms at 20 C 68 F If there is no continuity, replace the VSV. Fig. 50 Checking Vacuum Switching Valve...
Data Link Connector Dlc
The vehicle's ECM uses the ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format. Fig. 28 Identifying DLC3 Connector Terminals Fig. 28 Identifying DLC3 Connector Terminals 2007 ENGINE PERFORMANCE Engine Control System 2UZ-FE - Sequoia CANL 14 - CG 4 _ LOW-level CAN bus line Ignition switch OFF 200 ohms or higher If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and...
Ng Check For Shorts In All Harnesses And Connectors Connected To Fuse And
3. CHECK SKID CONTROL ECU TERMINAL VOLTAGE BM, BS a. Disconnect the skid control ECU connector. b. Measure the voltage between terminal BM BS and GND of the skid control ECU harness side connector. Voltage 10 to 14 V OK REPLACE SKID CONTROL ECU Fig. 59 Checking Skid Control ECU Terminal Voltage BM, BS NG GO TO Next Step Fig. 59 Checking Skid Control ECU Terminal Voltage BM, BS NG GO TO Next Step 4. CHECK HARNESS AND CONNECTOR SKID CONTROL ECU - BODY GROUND a. Disconnect the skid control ECU...
Check Driver Side Squib Nd Step Circuit For Short
a. Release the activation prevention mechanism built into connector B See CHECK MODE PROCEDURE . b. Measure the resistance according to the value s in the table below. OK
Install Rear Drive Pinion Companion Flange Subassembly
b. Coat the threads of a new nut with hypoid gear oil. c. 2WD Torque the companion flange nut. 1. Install the 3 stud bolts so that the heads come out 40 mm 1.57 in. . 2007 DRIVELINE AXLES Differential - Sequoia Fig. 154 Installing Stud Bolts So That Heads Come Out 40 Mm 1.57 In. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 154 Installing Stud Bolts So That Heads Come Out 40 Mm 1.57 In. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2. Set the SST and install the 3 nuts to the companion...
Check Trac Off Indicator Light
a. Connect the intelligent tester to the DLC3. b. Turn the ignition switch to the ON position and push the intelligent tester main switch ON. c. Select ACTIVE TEST mode on the intelligent tester. d. Check that ON and OFF of the TRAC OFF indicator light can be shown on the combination meter with the intelligent tester.
A Replace Skid Control Ecu Dtc C Vsc Sensor Output Voltage Malfunction
Supplies power to the VSC sensors yaw rate and master cylinder pressure sensors through terminal IG1. Voltage from VSC sensor system to ECU is abnormal. Fig. 76 VSC Sensor Output Voltage Malfunction - Wiring Diagram INSPECTION PROCEDURE a. Disconnect the master cylinder pressure sensor connectors No. 1 and No. 2. 1. Turn the ignition switch to the ON position. 2. Measure the voltage between terminal VCM and E1, VCM2 and E2 of the harness side connector. Fig. 77 Identifying Master Cylinder...
NOTE When replacing the yaw rate deceleration sensor perform the zero point
a. Check the yaw rate sensor installation. OK The sensor should be tightened to the specified torque. The sensor should not be tilted. NG INSTALL YAW RATE SENSOR CORRECTLY Torque 5 N m 10 kgfcnn, 3.7 ft 1bf Torque 5 N m 10 kgfcnn, 3.7 ft 1bf Fig. 55 Locating Yaw Rate Sensor Bolts Fig. 55 Locating Yaw Rate Sensor Bolts
NOTE Be careful not to damage the installation surface
Torque 73 N m 744 kgf cm, 53 ft. lbf 2007 DRIVELINE AXLES Differential - Sequoia Fig. 101 Removing Nuts, Washers amp Differential Carrier Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 1. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY a. Using a dial indicator, measure the vertical and lateral runout of the companion flange. Maximum runout 0.09 mm 0.0035 in. If the runout exceeds the maximum, replace the companion flange. 2007 DRIVELINE AXLES Differential - Sequoia...
Inspect No Air Switching Valve
a. Disconnect the vacuum hose from the VSV for the air injection system. b. Apply vacuum 30 kPa 306 gf cm2 , 4.35 psi to vacuum hose, check that the vacuum does not decrease. If operation is not as specified, replace the No.2 air switching valve. 2007 ENGINE Emission Control - Sequoia Fig. 20 Disconnecting Vacuum Hose From VSV For Air Injection System Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 20 Disconnecting Vacuum Hose From VSV For Air Injection System Courtesy of TOYOTA MOTOR SALES,...
Differential Vacuum Actuator Operation
If the operation is not as specified, replace the actuator assembly. If the operation is not as specified, replace the actuator assembly. 2007 DRIVELINE AXLES Differential - Sequoia
Check Fuel Cutoff Valve And Fill Check Valve
a. Disconnect the vent line hose from the fuel tank. b. Connect the pressure gauge to the fuel tank. c. Fill the fuel tank with fuel. d. Apply pressure of 4 kPa 41 gf cm2 , 0.58 psi to the vent port of the fuel tank. HINT It is necessary to check the amount of fuel in the fuel tank. When the fuel tank is full, the float valve of the fill check valve is closed and no air can pass through. e. Remove the fuel cap, and check that the pressure drops. 2007 ENGINE Emission Control - Sequoia If the...
Check Rsca Off Indicator
a. Check that the RSCA OFF indicator is off when turning the ignition switch to the ON position. b. Check that the RSCA OFF indicator comes on when turning the RSCA OFF switch on press the switch for approximately 2 seconds with the ignition switch on. c. Turn the ignition switch to the LOCK position with the RSCA OFF indicator is on, and then turn the ignition switch to the ON position. Check that the RSCA OFF indicator is off. 2007 RESTRAINTS Supplemental Restraint System - Sequoia Fig. 46...
Inspect Water Pump
a. Visually check the air hole and water hole for coolant leakage. If leakage is found, replace the water pump and timing belt. b. Turn the pulley, and check that the water pump bearing moves smoothly and quietly. If necessary, replace the water pump. Fig. 7 Checking Air amp Water Hole For Coolant Leakage Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 7 Checking Air amp Water Hole For Coolant Leakage Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. a. Remove the 4 nuts and fan from the fluid...
Check Srs Warning Light
a. Turn the ignition switch to the ON position, and check that the SRS warning light comes on for approximately 6 seconds primary check . b. Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to the ON position constant check . When any of the following symptoms occur, refer to the Problem Symptoms Table See PROBLEM SYMPTOMS TABLE . The ignition switch is turned from the LOCK to ON position, but the SRS warning light does not come on. 2007...
Inspect Charcoal Canister Assembly
a. Visually check the charcoal canister for cracks or damage. If cracks or damage are found, replace the charcoal canister assembly. 2007 ENGINE Emission Control - Sequoia Fig. 43 Inspecting Charcoal Canister Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 43 Inspecting Charcoal Canister Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. b. Check charcoal canister operation. 1. With the purge port closed, blow 1.67 kPa 17.0 gf cm2 , 0.24 psi of air into the vent port, and check...
Check Curtain Shield Airbag Assembly Lh Curtain Shield Airbag Lh Squib
a. Turn the ignition switch to the LOCK position. b. Disconnect the negative - terminal cable from the battery, and wait for at least 90 seconds. Disconnect the service wire from connector C. d. Connect the connector to the curtain shield airbag assembly LH. e. Connect the negative - terminal cable to the battery, and wait for at least 2 seconds. f. Turn the ignition switch to the ON position, and wait for at least 60 seconds. g. Clear the DTCs stored in memory See DTC CHECK CLEAR . h. Turn the...
OK SLIP indicator operates
NG GO TO step 3 OK GO TO Next Step a. Clear the DTC See DTC CHECK CLEAR . b. Turn the ignition switch OFF. c. Turn the ignition switch to the ON position, and check if the same DTC still remains in the memory. 3. CHECK HARNESS AND CONNECTOR TRANSLATE ECU - SKID CONTROL ECU NG REPAIR OR REPLACE HARNESS OR CONNECTOR 4. CHECK HARNESS AND CONNECTOR TRANSLATE ECU - COMBINATION METER NG REPAIR OR REPLACE HARNESS OR CONNECTOR a. Perform combination meter troubleshooting See HOW TO PROCEED WITH...
Rear Differential Carrier Assembly
2007 DRIVELINE AXLES Differential - Sequoia 2007 DRIVELINE AXLES Differential - Sequoia Torque 110 N m 1,122 kgf cm, 81 ft. lbf 2. DRAIN DIFFERENTIAL OIL Torque 49 N m 500 kgf cm, 36 ft. lbf a. Using SST, disconnect the brake line and remove the clip. Torque 15.5 N m 158 kgf cm, 11 ft. lbf b. Use the same procedure described above to the other side. Fig. 96 Disconnecting Brake Line amp Remove Clip Using SST Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 96 Disconnecting Brake Line amp Remove...
Connection Of Connectors For Side Airbag Sensor And Rear Airbag Sensor
a. Connect the connector as shown in the illustration. When locking, make sure that the outer returns to its original position and a click sound can be heard. 2007 RESTRAINTS Supplemental Restraint System - Sequoia When connecting, the outer will slide. Be sure not to hold the outer while connecting, as it may result in an insecure fit. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 2007 RESTRAINTS Supplemental Restraint System - Sequoia Fig. 26...
Inspect Front Drive Shaft Assembly
a. Check to see that there is no remarkable play in the outboard joint. b. Check to see that the inboard joint slides smoothly in the thrust direction. c. Check to see that there is no remarkable play in the radial direction of the inboard joint. Check the boots for damage. Fig. 6 Inspecting Front Drive Shaft Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 6 Inspecting Front Drive Shaft Assembly Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Dtc Trouble Detection Condition
ECU terminal STP voltage Is low when both ignition switch and stop light switch are ON. Fig. 64 Open In Stop Light Switch - Wiring Diagram INSPECTION PROCEDURE Fig. 64 Open In Stop Light Switch - Wiring Diagram INSPECTION PROCEDURE NOTE When replacing the skid control ECU, perform the zero point calibration See CALIBRATION . 1. CHECK STOP LIGHT SWITCH OPERATION a. Check that the stop light comes on when the brake pedal is depressed and turns off when the brake pedal is released. OK Stop light...
Check Brake Warning Light 1
a. Connect the intelligent tester to the DLC3. b. Turn the ignition switch to the ON position and intelligent tester main switch ON. c. Select the ACTIVE TEST mode on the intelligent. d. Check that ON and OFF of the BRAKE warning lieht can be shown on the combination meter NG GO TO step 3 OK GO TO Next Step a. Clear the DTC See DTC CHECK CLEAR . b. Turn the ignition switch OFF. c. Turn the ignition switch to the ON position, and check if the same DTC still remains in the 3. CHECK HARNESS AND...
CLEAR DTC Using the Intelligent tester
a. Connect the intelligent tester to the DLC3. b. Turn the ignition switch ON. d. Enter the following menus DIAGNOSIS ENHANCED OBD II DTC INFO CLEAR CODES. Fig. 29 Connecting Cable Of Intelligent Tester To DLC3 Fig. 29 Connecting Cable Of Intelligent Tester To DLC3 3. CLEAR DTC Without using the Intelligent tester a. Perform one of the following operations. 1. Disconnect the negative - battery cable for more than 1 minute. 2007 ENGINE PERFORMANCE Engine Control System 2UZ-FE - Sequoia 2. Remove...
Ng Replace Spiral Cable Ive
2007 RESTRAINTS Supplemental Restraint System - Sequoia a. Disconnect the cowl wire connector from the spiral cable. b. Measure the resistance according to the value s in the table below. TESTER CONNECTION SPECIFIED CONDITION CHART 2007 RESTRAINTS Supplemental Restraint System - Sequoia 2007 RESTRAINTS Supplemental Restraint System - Sequoia a. Measure the resistance according to the value s in the table below. 2007 RESTRAINTS Supplemental Restraint System - Sequoia 2007 RESTRAINTS Supplemental...
Disassemble Differential Case
a. Using a pin punch and hammer, remove the straight pin. b. Remove the pinion shaft, 2 pinion gears, pinion gear thrust washers, side gears and side gear thrust washers from the differential case. 2007 DRIVELINE AXLES Differential - Sequoia Fig. 51 Removing Straight Pin Using a pin punch amp hammer Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 51 Removing Straight Pin Using a pin punch amp hammer Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. 23. REMOVE FRONT DIFFERENTIAL CASE BEARINGS a....
NOTE Figures may show multiple component locations Refer to appropriate table
fiJC Magnetic Clutch and Lock Sensor Air Fuel Ratio Sensor Bank 1 Sensor 1 Air Fuel Ratio Sensor Bank 2 Sensor 1 Heated Oxygen Sensor Bank 1 Sensor 2 Camshaft Timing Oil Control Valve LH Heated Oxygen Sensor Bank 2 Sensor 2 Camshaft Timing Oil Control Vaive RH Electronically Controlled Transmission Solenoid Throttle Control Motor and Position Sensor Vehicle Speed Sensor Combination Meter Electronically Controlled Transmission Master Cylinder Pressure Sensor No,2 Power Seat Control SW Driver's...
Check Seat Position Sensor
a. Connect the connectors of the seat position sensor and the center airbag sensor assembly. b. Connect the negative - terminal cable to the battery, and wait for at least 2 seconds. c. Turn the ignition switch to the ON position, and wait for at least 60 seconds. d. Clear the DTCs stored in memory See DTC CHECK CLEAR . e. Turn the ignition switch to the LOCK position. f. Turn the ignition switch to the ON position, and wait for at least 60 seconds. g. Check the DTCs See DTC CHECK CLEAR .
OK VSC TRAC warning light operates
2. CHECK HARNESS AND CONNECTOR SKID CONTROL ECU - COMBINATION METER NG REPAIR OR REPLACE HARNESS OR CONNECTOR a. Perform combination meter troubleshooting See HOW TO PROCEED WITH TROUBLESHOOTING . NG REPAIR OR REPLACE COMBINATION METER The BRAKE warning light comes on when the brake fluid is insufficient, the parking brake is applied or the EBD is defective. The skid control ECU is connected to the translate ECU via the CAN1 communication system. WIRING DIAGRAM Fig. 85 Brake Warning Light...
Tc And Cg Terminal Circuit Description
DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are displayed by blinking of the SRS warning light. WIRING DIAGRAM 2007 RESTRAINTS Supplemental Restraint System - Sequoia Fig. 320 TC And CG Terminal Circuit - Wiring Diagram Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 320 TC And CG Terminal Circuit - Wiring Diagram Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. When each warning light stays blinking, a ground short in the wiring of the terminal TC of the DLC3...
Remove Front Wheel
Fig. 4 Identifying Front Axle Hub Components Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 4 Identifying Front Axle Hub Components Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. b. Remove the front disc brake cylinder. d. Inspect the axle hub backlash. 1. Using a dial indicator, measure the backlash near the center of the axle hub. Maximum backlash 0.05 mm 0.0020 in. If the backlash is greater than the maximum, replace the bearing. Fig. 5 Inspecting Axle Hub Backlash Courtesy of TOYOTA MOTOR...
NOTE Connect test leads from the back side of the connector The connectors
The voltage between the terminals of the ECM is kept constant regardless of the voltage of the A F sensor. 2007 ENGINE Emission Control - Sequoia Fig. 61 Measuring Voltage Between Terminals Of ECM Connectors Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. Fig. 61 Measuring Voltage Between Terminals Of ECM Connectors Courtesy of TOYOTA MOTOR SALES, U.S.A., INC. b. Connect a intelligent tester to the Controller Area Network Vehicle Interface Module CAN VIM . 2007 ENGINE Emission Control - Sequoia...